LOGIN

MDF-120-2

Vehicle Tracking Device

MDF-120-2

MDF-120-2

MDF-120-2

Small and professional tracker with internal high gain GNSS and GSM antennas, internal backup battery

MDF-120-2 features

Product Details

Product Overview

New generation GSM/GNSS module

New GNSS module

With new integrated GNSS module, Your tracking experience will be better than ever before. Even higher sensitivity, faster than ever cold start and almost instant hot start ensures that Your fleet will be tracked precisely.

Various vehicle CAN data

Various vehicle CAN data

With additional Max GPS Vehicle CAN adapters you will be able to acquire CAN data from any kind of transport such as light vehicles, trucks, buses, agriculture transport, and special transport. Supported vehicles list contains more than 1800 models.

1-Wire

1-Wire

1-wire protocol support enables you to identify your drivers and connect up to 4 temperature sensors. According to iButton® or RFID ID you can prevent unauthorized access to your fleet and temperature sensors allows you to monitor your cargo.

Small case

Small case

Easy to install, hard to find! Small case, internal GSM and GNSS antennas allow mount tracker much easier. Dimensions only 65x57x19 mm.

Trip detection

Trip detection

Easy trip start and stop detection gives you possibility to have the report with correct time, location and driven distance for each trip.

MDF-120-2 schema

Product Features

TECHNOLOGY

  • GNSS : Global positiong system/Global Navigation Satellite System.
  • GPRS : General Packet Radio Service (GPRS) is a packet oriented mobile data service based on the 2G technology.
  • SMS : Short Message Service (SMS) is a text messaging service component.

HARDWARE

  • Internal GSM antenna : An antenna used for GSM connectivity. Integrated into MDF device PCB. Does not have external connector.
  • Internal GNSS antenna : An antenna used for GPS connectivity. Integrated into MDF device PCB. Does not have external connector.
  • DIN - digital input - 3 : Digital Inputs allow device to detect logic states 1 (enabled) or 0 (disabled).
  • AIN - analog input - 1: An analog input converts a voltage level into a digital value that can be stored and processed in device.
  • DOUT - 2 : Digital Outputs allow device to output logic states 1 (makes a circuit) and 0 (cuts the circuit).
  • 1-Wire® - 1 : 1-Wire® is a device communications bus system that provides low-speed data, signaling, and power over a single conductor.
  • Battery - 170mAh Li-ion 3,7V : Allows device to work without external power source
  • Accelerometer : Accelerometer allows the device to indicate if vehicle is moving or not, as well as measure acceleration.
  • IP41 : Protected from tools and small wires, condensation.
  • 1MB memory : Internal memory for records storing when there is no GPRS connectivity.
  • 10 - 30V : External voltage range.
  • Overvoltage protection : Protects device from voltage jumps till 90V.
  • 1x SIM Card Allows to put 1 SIM card for internet connection
  • USB 2.0 Interface : Device accessible and configurable via USB.

FIRMWARE

  • LV-CAN support : LV-CAN200 is used to listen data from light vehicles. With this adapter MDF device is able to collect and send such data.
  • ALL-CAN support : ALL-CAN300 is used to listen data from any type of transport: light vehicles, Trucks, busses, agriculture and other special transport. With this adapter MDF device is able to collect and send such data.
  • Ignition detection : A vehicle ignition detection function, based on a configured ignition source (External power voltage, Digital input 1 or Movement).
  • Geo-fence : A functionality, which generates an event when crossing a defined area. It can be used to detect wherever car enters or leaves customized areas
  • Sleep/Deep sleep : Working modes which let MDF deviceto reduce power consumption and save vehicle battery.
    - In sleep mode, MDF device turns GNSS module off and it is not saving or sending new periodic data records.
    - In deep sleep mode, MDF devicesets GNSS receiver to sleep mode and turns off GSM/GPRS module, although periodic records with last known coordinate are being saved and sent to server.
  • Overspeeding detection: This scenario helps to prevent from exceeding fixed speed and inspects driver if needed. Digital output 1 is controlled by scenario for user needs, to manage buzzer, LED etc. During overspeeding event Digital output 1 will be turning ON and OFF until speed is lower than configured Max Allowed Speed.
  • FOTA : Firmware over the air solution. The software is used to send firmware/configuration to MDF devicevia GPRS network.
  • Remote Log : This type of MDF data logging is used when there is no possibility to connect to device physically. Device establishes GPRS connection and activates link to server, log is started to stream to server until set time is elapsed.
  • GPRS commands : It is possible to send commands to MDF deviceusing GPRS. GPRS commands can be used for sending configuration, debug, digital outputs control commands etc. These commands should be coded into a special codec12 format.
  • RFID 1-Wire®: Radio-frequency identification (RFID) is the use of a wireless non-contact system to transfer data from a tag attached to an object, for the automatic driver identification. Reader can be connected to MDF device via 1-wire interface.
  • iButton 1-Wire®: iButton is a special driver identification chip based on 1-wire protocol. External 1-wire iButton reader can be used in parallel with MDF devices
  • Temp. 1-Wire®: A temperature sensor which can be connected to MDF device and provide information via 1-wire data protocol.
  • Immobilizer: With this scenario vehicle can be used only if iButton is connected. You can connect any iButton to pass Immobilizer security. MDF device Digital Output 2 is controlled by scenario for user needs (for example: LED, buzzer or other indicator can be connected).
  • Green driving : Helps to prevent and inspect driver about harsh driving. This functionality works in parallel with accelerating force, braking force and cornering angles. Every harsh drive event can be presented in the real time during the LED or buzzer notification.
  • Fuel monitoring LLS : Fuel monitoring via LLS sensors gives ability to measurer are highly accurate fuel level in the vehicle. This functionality can be based on digital or analog connectivity.
  • Jamming detection: Jamming detection informs the driver with buzzer or LED about radio jamming events.
  • NTP time synch.: Network time protocol (NTP) is used to get the right time without GPS connection. This functionality gives an ability to monitor the device state in the real time.
  • SMS event : SMS event is a special functionality which is used to notify the user about the tracker initial state. Any changes of speed, engine status, over speeding or etc. will be informed with SMS.
  • Odometer : Odometer is used to calculate traveled distance and produce this information directly to server.
  • Trip detection : Trip detection is used to inform user about start and stop points in the dedicated location, while engine is on or off.
  • Integrated scenarios : The integrated device scenarios are used to simply enable the dedicate functionality like Green driving, Over speeding, Authorized driving or Immobilizer.
  • Remote configuration over SMS : The remote configuration via SMS gives an ability to configure the device via SMS
  • Offline tracking : Offline tracking is used to track the object position while GPRS is not activated.
  • Auto Geofencing : Auto geofencing can detect wherever car enters or leaves customized areas with deactivated ignition.

Technical Details

GSM/GPRS features:

  • Quad-band 900/1800 MHz; 850/1900 MHz
  • GPRS Multi-Slot Class 12 (up to 240 kbps)
  • GPRS Mobile Station Class B
  • SMS (text/data)

GNSS:

  • Tracking: 33/ 99 acquisition channels
  • -165 dBM sensitivity
  • Hot start < 1s
  • Warm Start < 25s
  • Cold start < 35s
  • NMEA-183 protocol
  • GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
  • Accuracy < 3m

Interface:

  • 1 Digital Input Reserved for Ignition Status Monitoring
  • 2 Digital Inputs
  • 1 Analog Input (10V or 30V range)
  • 2 Digital Open-collector Outputs (connecting external relays, LED, buzzers etc.)
  • 1-Wire® temperature sensor
  • 1-Wire® iButton
  • Motion sensor
  • Power supply (+10...+30) V DC
  • Internal high gain GSM antenna
  • Internal high gain GNSS antenna
  • Integrated LiPo back-up battery
  • Dimensions: L(65mm)xW(56,6mm)xH(18,9mm)
  • 2 Status LEDs
  • USB Port

For product enquiry and more details

CONTACT US

we will try to contact you as soon as possible

Quick Links

Services

Get In Touch

  • PO Box. 11394, Jawad Center
  • King Fahd Road, Al Nuzhah
  • Jeddah-21453, Saudi Arabia
  • Tel: +966 92 001 5111
  • Email:

© 2022-23 - Max GPS Track. All Rights Reserved